What's the best floor scrubber setup for VCT tile?

Short answer

For VCT, scrub daily with a red pad on a disk deck, and use an orbital deck for recoat prep or to strip finish with water and no stripper chemical. Six FactoryCat scrubbers offer that deck: a walk-behind for up to 31,568 sq ft in a 2-hour window at practical rates, the Pilot or GTX rider above that. Any pad rougher than red starts cutting finish.

Why is VCT its own cleaning problem?

VCT, or vinyl composition tile, is almost always coated with layers of floor finish. The finish is what you walk on and what you clean. It is there to wear, so the tile does not.

So the job is to take soil off the finish without taking the finish with it. Scuffs and black marks sit in the finish, not the tile, and tracked-in grit dulls it a little at a time.

That makes aggressiveness the key setting. Most pad makers follow a rough colour code: the lighter the pad, the gentler it is. White pads polish and buff. Red pads do light cleaning. Blue pads scrub harder, green pads harder still, and brown or black pads strip finish. Colours vary by pad maker, so read the maker's grade on the pack.

On finished VCT, red is as rough as routine work goes. Blue and green start to take finish off, so keep them for recoat prep, or blue for a deep scrub that red cannot shift. Stripping pads and grit brushes cut right through it.

Many sites also burnish VCT between scrubs, with a high-speed machine and a polishing pad. That is a separate job. Scrub first and let the floor dry, so you polish clean finish, not dirt.

Which floor scrubber is best for VCT?

Pick one of the six FactoryCat scrubbers with an orbital deck, the deck FactoryCat lists for "VCT Prep & Recoat". Then size it to your floor. The four walk-behinds cover up to 7,308 sq ft per hour (MicroMini), 12,059 (Micro-HD), 13,454 (Mini-HD) and 15,784 (Mag-HD). The two riders cover up to 18,000 (Pilot) and 21,661 (GTX).

These are practical rates, based on ISSA 2010 cleaning times. FactoryCat gives one rate per machine, not per deck, and publishes no stripping rate. Orbital decks run from 20 inches on the MicroMini and Micro-HD to 32 inches on the Mag-HD and GTX.

At its rate, the Mag-HD covers up to 31,568 sq ft in a 2-hour window. That is simple arithmetic, not a FactoryCat rating. Above that, look at the Pilot or GTX. The GTR and XR riders cover more per hour, but take no orbital deck. The floor scrubber sizing guide works through the math.

All six also offer a disk deck, and each model page lets you choose the scrub system. FactoryCat does not publish whether one machine can change between a disk and an orbital deck, so ask your dealer before you order. If you can have only one deck and you recoat or strip in-house, take the orbital deck. If an outside crew does that work, take the disk deck.

How should you set up for routine scrubbing?

Dust-mop or sweep first. The disk and orbital decks are not built to pick up loose debris, and grit caught under a pad scratches the finish. Then use the disk deck with a pad, not a brush, and keep grit brushes off finished VCT. FactoryCat's disk deck text points to pads here: "For flat, smooth, finished floors, a pad holder and disposable floor scrubber pads can be used."

Fit the red tufted pad driver from FactoryCat's brush and pad chart, with a gentle pad on it. In the common colour code, that is a red pad. White is for polishing. Red lifts surface soil and light scuffs without cutting the finish. The driver is a holder, not a red pad. FactoryCat's brush colours are a separate scheme: a black polypropylene brush is medium to light, but a black pad is usually a stripping pad.

Fill the tank with a neutral cleaner made for finished floors, mixed as its maker directs. A harsh cleaner can dull the finish. Use the least solution flow that cleans. If your model lets you set down pressure, start low. On the six orbital models, FactoryCat rates brush down pressure from up to 100 lbs (MicroMini) to up to 200 lbs (GTX).

Took only the orbital deck? Use it for routine scrubbing too, with a gentle pad. FactoryCat names no pad for the orbital deck, so ask your dealer which one suits daily work on finish.

If red leaves a few marks, go over those spots again, or try blue on that spot only. If it leaves soil across the floor, the floor is due a deep scrub. Do not make a rougher pad the daily pad.

How should you set up for a deep scrub or recoat?

A deep scrub takes off ground-in soil and keeps the finish. A scrub and recoat goes further. It takes off the worn top coats, and then you lay fresh coats on top. Both remove less than a full strip.

The orbital deck is FactoryCat's answer for both. An orbital deck, which some buyers call oscillating, moves its pad in small, fast orbits instead of spinning it, so the whole pad face stays flat on the floor. FactoryCat names no pad for it, so ask your dealer which grade suits your finish.

On a disk deck, a deep scrub starts with red. Move to blue only if red leaves soil, and never make blue the daily pad. For a scrub and recoat, fit a blue or green pad chosen to take off the worn top coats, not the whole finish. Then recoat as your finish maker directs.

How should you set up to strip VCT?

A full strip takes all the finish off, down to bare tile, before new coats go on. With a scrubber, there are two common ways to strip VCT.

The first is the orbital deck, with water and no stripper chemical. FactoryCat says the deck is "ideal for deep scrubbing and chemical free stripping. No floor stripper, reduces costs, eliminates unintended damage, and significantly reduces slip and fall risk." It also lists a "Reduction in Water Usage", printed in its newest brochure with no figure. Ask your dealer which pad to fit, and test a small area first. Very heavy build-up can still need a chemical strip.

The second is the chemical way, which FactoryCat does not list for its disk deck: a disk deck with a brown or black stripping pad and a stripper chemical, used as the stripper maker directs. The squeegee and vacuum pick up the slurry of stripper and old finish.

Either way, plan to do edges and corners by hand. The article on chemical-free stripping covers the orbital method step by step.

How do you get the water back up on sealed VCT?

Finished VCT is sealed, so it does not soak up water. What the squeegee misses stays on top and dries as streaks. Water left in the seams between tiles can also work its way under them.

So pickup matters as much as scrubbing. Water lift is how hard the vacuum pulls. Airflow is how much air it moves. On the six orbital models, FactoryCat rates 68 to 73 inches of water lift and 70 to 96 cfm. The GTX rates highest on both, at 73 inches and 96 cfm.

Help the vacuum along. Keep the squeegee blades clean, and turn or change them when they wear. Slow down at turns, overlap passes, and check that the floor dries clean.

Side-by-Side Comparison

Pad or brushHow aggressiveUse on VCTRisk to the finish
White padGentlest; polishesPolishing, not scrubbingVery low
Red padLightRoutine scrub on a disk deckLow
Blue padMediumDeep scrub if red fails; recoat prepStarts to take finish off
Green padHeavyScrub and recoat prepCuts into top coats
Brown or black padStripsFull strip, with stripper chemicalTakes finish to bare tile
Soft brush (nylon, tampico)Soft to lightNot needed on flat VCTLow
Grit brushMedium to extreme roughNone on finished VCTCuts through finish
Pad on the orbital deckSet by the pad fittedDeep scrub, recoat prep, strip with waterDepends on the pad; ask your dealer

Micro-HD v2.1

Agile, quiet, and powerful, this compact industrial walk-behind floor scrubber is ready to take on smaller spaces with any floor type. Rubberized floors, grouted tile, exposed aggregate and concrete floors are no match. Select our SUDS on board soap dilution system to better control your cleaning chemical costs. Available in 20”(51cm) - 26”(66cm) scrub width.

Mag-HD v2.2

For large areas not big enough for a ride-on floor scrubber, but where maximum output is required from an industrial grade walk behind floor scrubber, the Mag-HD v2 is the clear winner. Offering exceptional run time that allows you to scrub a long time on a single charge. Multiple scrub deck options generate high operator productivity. Include an optional Spray Jet spray wand to increase the cleaning capabilities beyond that of a typical scrubber. Available in 28”(71cm) - 34”(86cm) scrub width.

Pilot v3

Ultra-maneuverable, this micro rider affords you the efficient cleaning of an industrial ride-on floor scrubber with a footprint smaller than many large walk-behind auto scrubbers. Able to navigate tight isles, narrow doorways, and smaller elevators this ride-on auto scrubber is best in class. Available in 25”(64cm) - 28”(71cm) scrub width.

GTX v2.2

Navigation of your facility is easy with this compact ride on auto scrubber. Say, “so long” to the fatigued operator from walking behind a traditional auto scrubber. With this industrial ride on floor scrubber your staff will clean more square footage during their shift and still have the time and energy to do additional work. With impressive down pressure and brush speed this machine cleans your toughest dirt. Available in 26”(68cm) - 33”(84cm) scrub width.
Yes, an orbital scrub deck can strip floor finish with water and no stripper chemical, because its pad scrubs in small, fast orbits instead of spinning. FactoryCat offers an orbital deck on six scrubbers and lists a "Reduction in Water Usage" for it. The trade-off is time and pad wear, and very heavy build-up can still need a chemical strip, so test a small area first.
Use pads on smooth, finished floors such as sealed VCT, and brushes on textured, grouted, uneven or bare concrete floors, where bristles reach low spots. On a FactoryCat scrubber, the disk deck takes either, the orbital deck takes pads, and the cylindrical deck takes brushes only, in five of the nine options FactoryCat lists. Rougher grades clean harder but wear the finish and load the motor more.
Pick a disk deck for wavy or smooth finished floors, a cylindrical deck for grouted tile or small loose debris, and an orbital deck to strip floor finish without chemicals. FactoryCat sells all three: disk on every scrubber, cylindrical on six models, orbital on six. Orbital tops out at a 32-inch scrub path and is not offered on the two largest riders.

Frequently Asked Questions

What colour pad should I use on VCT every day?

In the common colour code, red, on the disk deck's red tufted pad driver. White is for polishing. Colours vary by pad maker, so check the maker's grade. If red leaves soil, try blue on that spot, but never make blue the daily pad, because it starts to take finish off.

Can I use a cylindrical deck on VCT?

FactoryCat does not list it for VCT. It names that deck for concrete, grouted tile and other flat, durable surfaces, and it takes brushes only. For VCT, choose the disk or orbital deck.

What PSI should I run on VCT?

FactoryCat publishes no PSI figure, only brush down pressure in pounds, per machine. On the six orbital models it runs from up to 100 lbs on the MicroMini to up to 200 lbs on the GTX. If you can set the pressure, use the lowest setting that cleans.

Does the same setup work on luxury vinyl tile?

Not always. Many luxury vinyl tiles have a factory wear layer, not a finish you strip and replace, so a rough pad or a strip can cut into the floor itself. Check the floor maker's care guide first.