Can an orbital deck strip floor finish without chemicals?

Short answer

Yes, an orbital scrub deck can strip floor finish with water and no stripper chemical, because its pad scrubs in small, fast orbits instead of spinning. FactoryCat offers an orbital deck on six scrubbers and lists a "Reduction in Water Usage" for it. The trade-off is time and pad wear, and very heavy build-up can still need a chemical strip, so test a small area first.

How does an orbital deck strip finish without chemicals?

A rotary disk deck spins a round brush or pad in one direction. To strip finish with it, you normally spread a stripper chemical first. The chemical softens the finish, and the spinning pad lifts it.

An orbital deck, which buyers also call an oscillating deck, works another way. The pad does not spin. It moves in small, fast orbits, so the whole face of the pad stays flat on the floor. That steady contact scrubs the finish off by abrasion. The pad and water do the work, not a chemical.

In FactoryCat's words, the scrubbing power of its orbital deck "makes it ideal for deep scrubbing and chemical free stripping." FactoryCat builds the deck with isolators, bearings and a metal-backed pad holder.

On its two riders with this deck, FactoryCat rates the orbital motor at 1.5 hp on the Pilot and 1 hp on the GTX, both at 2,700 RPM. That is the motor's rating, not a pad speed.

What do you save by stripping without chemicals?

The first saving is the stripper itself. There is no chemical to buy, store, mix or get rid of. FactoryCat sums it up this way: "No floor stripper, reduces costs, eliminates unintended damage, and significantly reduces slip and fall risk."

Water is the second. FactoryCat lists a "Reduction in Water Usage" for the orbital deck. Its newest brochure prints that bullet with no figure, and no gallons figure is published either.

What you pick up changes too. A chemical strip leaves a slurry of stripper and softened finish on the floor. With the orbital deck, the scrubber's squeegee and vacuum pick up water and old finish, with no stripper in it.

You also skip steps. There is no stripper to spread, no wait while it soaks in, and no stripper to rinse back out. Your time goes into scrub passes instead. FactoryCat publishes no stripping rate, and its sq ft per hour figures are per machine, not per deck.

Where does chemical-free stripping fall short?

It is a mechanical job. The pad does all the work, with no chemical to loosen the finish first. So thick or old finish can take more than one pass, and pads wear as they cut. Keep spare pads on hand. Nothing is published on how many coats come off per pass.

It will not suit every floor. With no stripper, there is no chemical to harm the floor, but the pad still cuts whatever it touches. On a floor with a factory wear layer, such as many luxury vinyl tiles, it can cut into the floor's own surface. Very heavy build-up can still need a chemical strip to reach bare floor.

It is not on every machine. The GTR and XR riders and the Rebel stand-on do not take an orbital deck. The widest orbital path is 32 inches, while the XR's disk deck reaches 45 inches. On a very large floor, that means more passes.

So test first. Pick a small area out of the way and run the deck. Time it, note how much water it uses, and check the result once the floor is dry. If the finish comes off cleanly in a few passes, the method fits your floor.

Is a full strip the same as prep and recoat?

No. A full strip takes all the finish off, down to the bare floor, before you lay new coats. Prep and recoat takes off only the worn top layers, then you add fresh coats on top. It removes less, so it is a lighter job.

FactoryCat lists both "Chemical Free Stripping" and "VCT Prep & Recoat" as orbital-deck benefits. So one deck covers both jobs. How far you go depends on how many passes you make and which pad you fit.

How do you strip a floor with an orbital deck?

First, sweep or dust-mop the floor. The orbital deck is not built to pick up loose debris, so it needs a clean floor to work on.

Next, fit the pad to the metal-backed pad holder. Ask your dealer which pad suits your finish and how far you want to go.

Then scrub your test area with water only, and let the squeegee and vacuum pick up behind you. Let it dry and check it. If it looks right, work the room in overlapping passes. Go back over any spots where finish is left.

A scrub deck cannot reach right into edges and corners, so plan to strip those by hand.

Once the floor is clean and dry, refinish it as your finish maker directs.

Which FactoryCat machines have an orbital deck?

Six do: the MicroMini, Micro-HD, Mini-HD and Mag-HD walk-behinds, and the Pilot and GTX riders. Orbital scrub paths run from 20 to 32 inches.

The walk-behinds suit rooms, corridors and smaller floors. The MicroMini and Micro-HD take a 20 or 24-inch orbital deck. The Mini-HD takes 24 or 28 inches, and the Mag-HD 28 or 32 inches.

The riders suit large open floors. The Pilot takes a 24 or 28-inch orbital deck, and the GTX 28 or 32 inches.

For stripping, weight on the pad matters, because the pad does all the cutting. FactoryCat gives brush down pressure in pounds, per machine, not per deck. On the orbital models it runs from up to 100 lbs on the MicroMini to up to 200 lbs on the GTX, and the Mag-HD is highest among the walk-behinds, at up to 185 lbs. Ask your dealer what the orbital deck itself puts down.

Side-by-Side Comparison

MethodChemical strip, rotary diskChemical-free, orbital deck
What removes the finishStripper softens it, pad lifts itPad scrubs it off with water
Stripper to buy and dispose ofYesNone
Water useNot publishedListed benefit; no figure
What you pick upStripper slurry and old finishWater and old finish
Typical stepsApply, wait, scrub, pick up, rinseScrub with water, pick up, repeat as needed
Best fitBuild-up a pad alone cannot shiftStripping, prep and recoat, VCT
Pad holderPad driver on a disk deckMetal-backed pad holder
FactoryCat scrub pathsDisk 17"–45"Orbital 20"–32"
FactoryCat decksDisk on every scrubber; stripping not listedOrbital on 6 models

Mini-HD v2.1

With the perfect balance of maneuverability and productivity, the Mini-HD v2 will simplify and improve your cleaning. This mid-sized industrial walk-behind floor scrubber offers battery pack options, available ZerO3 On-Demand Aqueous Ozone chemical free cleaning system, and selectable tires. This industrial grade floor scrubber can be customized to fulfill your needs. Available in 20”(51cm) - 29”(74cm) scrub width.

Mag-HD v2.2

For large areas not big enough for a ride-on floor scrubber, but where maximum output is required from an industrial grade walk behind floor scrubber, the Mag-HD v2 is the clear winner. Offering exceptional run time that allows you to scrub a long time on a single charge. Multiple scrub deck options generate high operator productivity. Include an optional Spray Jet spray wand to increase the cleaning capabilities beyond that of a typical scrubber. Available in 28”(71cm) - 34”(86cm) scrub width.

Pilot v3

Ultra-maneuverable, this micro rider affords you the efficient cleaning of an industrial ride-on floor scrubber with a footprint smaller than many large walk-behind auto scrubbers. Able to navigate tight isles, narrow doorways, and smaller elevators this ride-on auto scrubber is best in class. Available in 25”(64cm) - 28”(71cm) scrub width.

GTX v2.2

Navigation of your facility is easy with this compact ride on auto scrubber. Say, “so long” to the fatigued operator from walking behind a traditional auto scrubber. With this industrial ride on floor scrubber your staff will clean more square footage during their shift and still have the time and energy to do additional work. With impressive down pressure and brush speed this machine cleans your toughest dirt. Available in 26”(68cm) - 33”(84cm) scrub width.
Pick a disk deck for wavy or smooth finished floors, a cylindrical deck for grouted tile or small loose debris, and an orbital deck to strip floor finish without chemicals. FactoryCat sells all three: disk on every scrubber, cylindrical on six models, orbital on six. Orbital tops out at a 32-inch scrub path and is not offered on the two largest riders.
For VCT, scrub daily with a red pad on a disk deck, and use an orbital deck for recoat prep or to strip finish with water and no stripper chemical. Six FactoryCat scrubbers offer that deck: a walk-behind for up to 31,568 sq ft in a 2-hour window at practical rates, the Pilot or GTX rider above that. Any pad rougher than red starts cutting finish.
Use pads on smooth, finished floors such as sealed VCT, and brushes on textured, grouted, uneven or bare concrete floors, where bristles reach low spots. On a FactoryCat scrubber, the disk deck takes either, the orbital deck takes pads, and the cylindrical deck takes brushes only, in five of the nine options FactoryCat lists. Rougher grades clean harder but wear the finish and load the motor more.

Frequently Asked Questions

Is an orbital deck the same as a dry-strip floor machine?

Not quite. A standalone orbital floor machine often strips dry, and you sweep or vacuum up the dust after. A FactoryCat orbital deck sits on a scrubber, which puts water down and picks the dirty water back up in the same pass.

How much water does orbital stripping use?

FactoryCat lists a "Reduction in Water Usage" for its orbital deck. Its newest brochure prints that bullet with no percentage, and it publishes no gallons figure. Solution tanks on the six orbital models hold 10 gallons (MicroMini) to 35 gallons (Mag-HD). These are tank sizes, not the water a strip uses.

Can a disk or cylindrical deck strip without chemicals?

FactoryCat lists chemical-free stripping for its orbital deck only. The cylindrical deck takes brushes, not pads. A disk deck takes pads through a pad driver, and stripping with one usually means using a stripper chemical.

Will chemical-free stripping work on my floor?

If it is VCT, that is the floor FactoryCat names for its orbital deck. On luxury vinyl or another floor with a factory coating, check the floor maker's care guide first. Either way, try a small area out of sight before the whole room.