What size floor scrubber do I need?

Short answer

Divide your cleanable floor area by the hours you have, then pick a machine whose practical rate beats that figure. FactoryCat walk-behinds have practical rates of up to 7,308 to 15,784 sq ft per hour and FactoryCat riders up to 18,000 to 29,374, based on ISSA 2010 cleaning times. A faster machine finishes sooner, but it has to fit your narrowest doorway and last the job on one charge.

How do you measure your floor for a scrubber?

First, find your cleanable floor area. Use a floor plan or a tape measure. Multiply the length by the width of each open area, then add them up.

Leave out floor the machine will not scrub: under racking and fixed equipment, carpet, and corners you clean by hand.

Second, set your cleaning window. This is the time one operator has for this floor in a shift, with the floor clear. Leave out other chores, but keep time inside it for refills and tank dumps.

While the tape is out, measure the narrowest doorway, aisle and ramp on the route. You will need them in the last step.

Which sq ft per hour figure should you plan with?

FactoryCat publishes two rates for each walk-behind and rider scrubber, both based on ISSA 2010 cleaning times: theoretical and practical. Plan with the practical rate.

On each, the practical rate is 44 to 47 percent of the theoretical, a little under half. The Mag-HD walk-behind is rated at up to 33,932 sq ft per hour theoretical and up to 15,784 practical. The XR rider is rated at up to 63,000 and up to 29,374. The percentage is simple division of the two published figures.

FactoryCat does not say what its practical rate allows for, so fit refills into your window too. Don't reduce it further with a rule of thumb. For a crowded floor, time a demo instead (step six).

How many hours will your floor take?

Third, divide your cleanable area by the machine's practical rate. That is the hours of scrubbing it needs. If it is more than your window, the machine is too small. Or work backwards: divide your area by your window to get the rate you need.

FactoryCat's practical rates are up to 7,308 sq ft per hour for the MicroMini, 12,059 for the Micro-HD, 13,454 for the Mini-HD and 15,784 for the Mag-HD. The riders run from up to 18,000 for the Pilot through 21,661 for the GTX and 23,627 for the GTR to 29,374 for the XR. So every FactoryCat rider covers more floor per hour than any FactoryCat walk-behind. Above 31,568 sq ft in a 2-hour window, or 47,352 sq ft in a 3-hour window, no FactoryCat walk-behind finishes in time.

The table below shows the floor each machine covers in 2 hours at its practical rate. Each runs longer than that on a charge. Find the first row at or above your area. For a 4-hour window, halve your floor area first. Then check run time, because the MicroMini, Micro-HD and Mini-HD run less than 4 hours on a charge. If your floor is bigger than the last row, you need a longer window, or a second machine and operator.

Note the Pilot row: it covers more floor than the Mag-HD with a narrower path and a smaller tank. Path width alone does not set the rate, so size by the rate first.

Will the battery and tanks last the job?

Fourth, check run time. The machine must scrub for the hours you worked out on one charge. Walk-behinds run up to 3 hours (MicroMini), 2.5 (Micro-HD), 3.5 (Mini-HD) and 5 (Mag-HD). Riders run up to 4 hours (Pilot), 4.5 (GTX) and 5 (GTR and XR).

If the machine cannot, pick a longer-running one, add a second machine, or split the floor across two shifts. FactoryCat does not publish charge times, so do not plan on a recharge mid-job.

Fifth, count tank refills. Divide the solution tank size by the top flow rate in gallons per minute (GPM). That gives the minutes a full tank lasts at maximum flow, the worst case. At half the flow, it lasts twice as long. On the walk-behinds, that is about 20 minutes on the MicroMini (10 gallons at 0.5 GPM), 26 on the Micro-HD (13 at 0.5), 30 on the Mini-HD (21 at 0.7) and 35 on the Mag-HD (35 at 1.0).

Rider tanks hold 22 gallons (Pilot) to 65 gallons (XR). Run the same sum with the flow rate in the spec table of FactoryCat's rider brochure, on its downloads page. Each time you refill, plan to empty the dirty-water (recovery) tank too. On every FactoryCat walk-behind and rider, the recovery tank is as big as the solution tank or bigger, such as 37 gallons against 35 on the Mag-HD.

How do obstacles, aisles and doorways change the answer?

Sixth, look at what is on the floor and how the machine gets there. Columns, rack ends, pallets and tight turns all slow a machine down. No figure is published for how much, so time a demo on your own floor.

A wider path covers more floor per pass, but only where the machine fits. Small rooms joined by doors suit a small machine, and one big open floor a wider one.

Check your narrowest doorway against the machine's widest point, not its scrub path. The MicroMini is 21 inches wide and 42 long, and the Pilot rider 27 wide and 54 long. The Mag-HD walk-behind is 31 wide and 62 long in its smallest build, and the XR rider 43 wide and 77 long. Published sizes may not include the deck or squeegee. The Mag-HD's disk path goes up to 34 inches, so ask for the widest point.

What does a worked example look like?

Take a warehouse with 50,000 sq ft of cleanable floor and a 4-hour window each night. The rate needed is 50,000 divided by 4, or 12,500 sq ft per hour. The Micro-HD falls short at about 4.1 hours. The Mini-HD passes on rate at about 3.7 hours, but its run time is up to 3.5 hours. The MicroMini would need about 6.8 hours, more than twice its run time of up to 3 hours.

The Mag-HD takes about 3.2 hours, inside its run time of up to 5 hours. At maximum flow its 35-gallon tank lasts 35 minutes, so the job needs about five refills after the first fill. At half flow it needs about two. That leaves about 50 minutes for them, so time one refill and dump at your fill point. If five take longer, run a lower flow or look at the Pilot.

The Pilot rider takes about 2.8 hours, inside its run time of up to 4 hours, and leaves about 1.2 hours for refills. Both fit on rate and run time. Pick the Mag-HD if your operator can walk for 3.2 hours and refills are quick. It holds more solution (35 vs 22 gallons) and runs longer (up to 5 vs up to 4 hours). Pick the Pilot to finish sooner with the operator seated.

Now cut the window to 3 hours. You need about 16,700 sq ft per hour, more than any FactoryCat walk-behind covers, so the answer becomes a rider. The Pilot takes about 2.8 hours and leaves under 15 minutes for refills. The GTX covers up to 21,661 sq ft per hour, so it takes about 2.3 hours and leaves about 40 minutes.

Side-by-Side Comparison

Area in 2 h at practical rateMachine (format)Disk scrub pathSolution tank
Up to 14,616 sq ftMicroMini (walk-behind)17" or 20"10 gal
Up to 24,118 sq ftMicro-HD (walk-behind)20" or 26"13 gal
Up to 26,908 sq ftMini-HD (walk-behind)26" or 28"21 gal
Up to 31,568 sq ftMag-HD (walk-behind)Up to 34"35 gal
Up to 36,000 sq ftPilot (rider)26" or 28"22 gal
Up to 43,322 sq ftGTX (rider)26"–34"33 gal
Up to 47,254 sq ftGTR (rider)30"–36"46 gal
Up to 58,748 sq ftXR (rider)40" or 45"65 gal

MicroMini

Nimble and tough, this durable micro scrubber is battery-powered and perfect for small spaces, tight areas, and hard-to-reach places, while still cleaning larger rooms quickly. This industrial floor scrubber easily navigates around obstacles, boosting efficiency compared to cleaning by hand. Available in 20” (51cm) - 26” (66cm) scrub width.

Mag-HD v2.2

For large areas not big enough for a ride-on floor scrubber, but where maximum output is required from an industrial grade walk behind floor scrubber, the Mag-HD v2 is the clear winner. Offering exceptional run time that allows you to scrub a long time on a single charge. Multiple scrub deck options generate high operator productivity. Include an optional Spray Jet spray wand to increase the cleaning capabilities beyond that of a typical scrubber. Available in 28”(71cm) - 34”(86cm) scrub width.

Pilot v3

Ultra-maneuverable, this micro rider affords you the efficient cleaning of an industrial ride-on floor scrubber with a footprint smaller than many large walk-behind auto scrubbers. Able to navigate tight isles, narrow doorways, and smaller elevators this ride-on auto scrubber is best in class. Available in 25”(64cm) - 28”(71cm) scrub width.

XR v2.0

The XR v2 battery powered industrial ride-on floor scrubber is made in America for large tough cleaning jobs. Large enough to be a warehouse floor scrubber, yet extremely maneuverable in narrow aisles. A 34 to 46 inch ride on floor scrubber that is simple to operate and not intimidating to the operator. Impressive operator visibility and comfort set us apart from the competition. Large capacity tanks and dual vacuums allow this ride on floor scrubber to finish the job fast!
Choose a rider for a large, open floor you want cleaned in fewer operator hours. Choose a walk-behind for smaller areas, crowded aisles and rooms you clean one at a time. Every FactoryCat rider covers more floor per hour than any FactoryCat walk-behind: up to 18,000 to 29,374 sq ft per hour against up to 7,308 to 15,784 (practical rates, ISSA 2010 cleaning times).
A stand-on scrubber is the middle ground: the operator rides standing, so it usually travels faster than a walk-behind and is quicker to step off than a seated rider. FactoryCat's stand-on, the Rebel, cleans a 20-inch path, the same as the 20-inch option on its smallest walk-behinds. Pick it for stop-and-go work in busy aisles, a walk-behind for small rooms, and a rider for big open floors.
Choose by what is on your floor: a sweeper for dry debris, a scrubber for wet or stuck-on soil, a sweeper-scrubber only when you get both every day. FactoryCat builds no sweeper-scrubber with a built-in sweeper; its cylindrical-deck scrubbers sweep light debris while scrubbing. For heavy dry debris, the TR sweeper covers up to 59,406 sq ft per hour (practical rate, ISSA 2010 times), twice FactoryCat's largest scrubber.

Frequently Asked Questions

When should you move from a walk-behind to a rider?

When you need more than 15,784 sq ft per hour in practical use. The Mag-HD covers up to that much, the most of any FactoryCat walk-behind. The Pilot, the smallest rider, covers up to 18,000. In a 2-hour window, the line falls at 31,568 sq ft of floor.

Where does the Rebel stand-on fit?

The Rebel is FactoryCat's only stand-on, with a 20-inch disk deck. No rate, tank size or run time is published for it, so you can't run this method on it. Ask for those figures, or time a demo on your own floor.

Does the scrub deck change the size you need?

It can, because a narrower deck cleans a narrower strip on each pass. FactoryCat gives one practical rate per machine and does not say which deck that rate assumes. The Mag-HD takes a disk deck up to 34 inches, a 29 or 33-inch cylindrical deck, or a 28 or 32-inch orbital deck. Pick the deck for your floor first, then time a demo with that deck.

How wide a scrub path do you need?

Let the hours decide first: pick the smallest machine whose practical rate fits your window. Then check it fits your narrowest doorway and turns in your aisles. FactoryCat walk-behind disk paths run from 17 to 34 inches, and rider disk paths from 26 to 45 inches.